Betekenis van:
signal level

Voorbeeldzinnen

1. Test level/functional status (for signal lines)
2. "Noise level" (6) means an electrical signal given in terms of power spectral density.
3. ‘signal word’ means a word that indicates the relative level of severity of hazards to alert the reader to a potential hazard; the following two levels are distinguished:
4. For the purposes of 6A006., ’sensitivity’ (noise level) is the root mean square of the device-limited noise floor which is the lowest signal that can be measured.
5. "Noise level" (6) means an electrical signal given in terms of power spectral density. The relation between "noise level" expressed in peak-to-peak is given by S2pp = 8 No(f2–f1), where Spp is the peak-to-peak value of the signal (e.g., nanoteslas), No is the power spectral density (e.g., (nanotesla)2/Hz) and (f2–f1) defines the bandwidth of interest.
6. "Noise level" (6) means an electrical signal given in terms of power spectral density. The relation between "noise level" expressed in peak-to-peak is given by S2pp = 8 No(f2–f1), where Spp is the peak-to-peak value of the signal (e.g., nanoteslas), No is the power spectral density (e.g., (nanotesla)2/Hz) and (f2–f1) defines the bandwidth of interest.
7. semaphores, mechanical signal discs, level-crossing control gear, signal and point controls, and other mechanical (including electro-mechanical) signalling, safety or traffic control equipment, whether or not fitted for electric lighting, for railways, tramways, roads, inland waterways, parking facilities, port installations or airfields.
8. ‘limit of detection’ means the output signal or concentration value above which it can be affirmed, with a stated level of confidence that a sample is different from a blank sample containing no determinand of interest;
9. Depending on the NOx level selected, the system shall activate a warning signal and in addition, if applicable, the torque limiter at any time before the end of the detection sequence.
10. an output level within 1 dB of the final output level. "Frequency synthesiser" (3) means any kind of frequency source or signal generator, regardless of the actual technique used, providing a multiplicity of simultaneous or alternative output frequencies, from one or more outputs, controlled by, derived from or disciplined by a lesser number of standard (or master) frequencies.
11. "Frequency switching time" (3 5) means the maximum time (i.e., delay), taken by a signal, when switched from one selected output frequency to another selected output frequency, to reach: a. A frequency within 100 Hz of the final frequency; or b. An output level within 1 dB of the final output level.
12. An output level within 1 dB of the final output level. "Frequency synthesiser" (3) means any kind of frequency source or signal generator, regardless of the actual technique used, providing a multiplicity of simultaneous or alternative output frequencies, from one or more outputs, controlled by, derived from or disciplined by a lesser number of standard (or master) frequencies.
13. An output level within 1 dB of the final output level. "Frequency synthesiser" (3) means any kind of frequency source or signal generator, regardless of the actual technique used, providing a multiplicity of simultaneous or alternative output frequencies, from one or more outputs, controlled by, derived from or disciplined by a lesser number of standard (or master) frequencies.
14. The relation between "noise level" expressed in peak-to-peak is given by S2pp = 8 No(f2–f1), where Spp is the peak-to-peak value of the signal (e.g., nanoteslas), No is the power spectral density (e.g., (nanotesla)2/Hz) and (f2–f1) defines the bandwidth of interest.
15. All measurements shall be made using the time constant ‘F’. The measurement of the over-all sound pressure level shall be made using the weighting curve A. The spectrum of the sound emitted shall be measured according to the Fourier transform of the acoustic signal.